ANDREWS CAMS

Designed with a combination of shorter durations and higher lifts to offer the advantages of a broad torque output through the entire rpm range Designed for hydraulics; but could be run with solids Grind #1 is the low-compression version of an ``A`` grind cam for 74`` and 80`` models Grind #2 offers more power through the rpm range for engines with low-compression pistons; the low-compression sister to a ``B`` grind cam Will not fit Evolution models

ANDREWS #1 CAM BT-78-84						$127.95
#1 Grind Cams For Low-Compression Mfg. #: 212150 Our #: P DS199324 Vendor #: DS-199324
For L77-84 FX; FL

ANDREWS CAMS

More valve lift and duration means extra power through the rpm (2000-6000+) range for bolt-in or modified engines Piston-valve clearance should be checked; uses stock valve springs Higher lift cams for modified Freedom motors with big cylinders and higher compression ratio More torque and HP with factory 100 kits; rpm range (2200-6500+) Uses high-lift valve springs

ANDREWS CAMS

CAMS V438 02-07 FREEDOM						$287.95
Mfg. #: 268450 Our #: P 09250193 Vendor #: 0925-0193
V-438

CAMS V460 02-07 FREEDOM						$287.95
Mfg. #: 268460 Our #: P 09250194 Vendor #: 0925-0194
V-460

ANDREWS CAMS

Similar to stock cams but timing is advanced for more torque and horsepower at low and middle rpms Easy installation; uses stock valve springs A little hotter cam that offers a big boost in horsepower and torque over entire rpm range Easy installation; uses stock valve springs A hotter cam with longer duration for motors with higher compression ratios and low restriction exhaust Brings a big boost in horsepower and torque at middle and upper rpms Easy installation; uses stock valve springs

ANDREWS CAMS

PL420 VICTORY CAMS						$264.95
Mfg. #: 268420 Our #: P DS199256 Vendor #: DS199256
PL420

PL402 VICTORY CAMS						$264.95
Mfg. #: 268402 Our #: P DS199257 Vendor #: DS199257
PL402

PL440 VICTORY CAMS						$264.95
Mfg. #: 268440 Our #: P DS199258 Vendor #: DS199258
PL440

ANDREWS CAMS

Andrews Products grinds its cams with the help of a computer with cam design capabilities. This superior technology gives the utmost in both performance and reliability. Only the best alloy steel billets and heat-treating processes are util Bolt-in cam for light bikes (FXRS; etc.) adds significant mid-range power without affecting idle A 6000+ rpm cam for stock heads and springs with hydraulic lifters Designed for mildly stroked motors or motors with head work done Works with stock hydraulics; with stock spring travel set to .560`` minimum Excellent power in the 2500-6500 rpm range Designed for big-inch stroker motors with head work Works with stock hydraulics; with stock spring travel set to .560`` minimum Excellent in the 2800-6500 rpm range Uses stock springs

ANDREWS CAMS

ANDR EV3 CAM.495 LIF84-99						$127.95
Mfg. #: 291130 Our #: P DS199320 Vendor #: DS-199320
EV3 Grind Cam

ANDREWS EV5 CAM 84-99 B-T						$127.95
Mfg. #: 291150 Our #: P DS199443 Vendor #: DS-199443
EV5 Grind Cam

ANDREWS EV7 CAM 84-99 B-T						$127.95
Mfg. #: 291170 Our #: P DS199445 Vendor #: DS-199445
EV7 Grind Cam

ANDREW EV-13 CAM 84-99EVO						$127.95
Mfg. #: 291113 Our #: P DS199323 Vendor #: DS-199323
EV13 Grind Cam

ANDREWS EV-23 CAM 84-99						$127.95
Mfg. #: 291123 Our #: P DS199097 Vendor #: DS-199097
EV23 Grind Cam

ANDREW EV-27 CAM 84-99EVO						$127.95
Mfg. #: 291127 Our #: P DS199344 Vendor #: DS-199344
EV27 Grind Cam

CAM EV31 EVO						$127.95
Mfg. #: 291117 Our #: P 09250071 Vendor #: 0925-0071
EV31 Grind Cam

ANDREWS EV38 CAM 84-99B-T						$127.95
Mfg. #: 291138 Our #: P DS199446 Vendor #: DS-199446
EV38 Grind Cam

ANDREW EV46 CAM 84-99 EVD						$127.95
Mfg. #: 291146 Our #: P DS199327 Vendor #: DS-199327
EV46 Grind Cam

ANDREWS EV59 CAM 84-99B-T						$127.95
Mfg. #: 291159 Our #: P DS199444 Vendor #: DS-199444
EV59 Grind Cam

ANDREWS EV51 CAM 84-99B-T						$127.95
Mfg. #: 291151 Our #: P DS199447 Vendor #: DS-199447
EV51 Grind Cam

ANDREW EV-72 CAM 84-99EVO						$127.95
Mfg. #: 291172 Our #: P DS199194 Vendor #: DS-199194
EV72 Grind Cam

CAMS FOR 48-84 BIG TWIN

More mid-range and top-end power for street and drag bikes. These cams work with solid or hydraulic lifters; and the idle remains unaffected up to 6000 rpm with stock valve springs. Cams bolt into 48-84 Big Twin engines with no head work Spring travel and clearance; plus clearance at main bearing boss must be checked on 80 and later models Bolt-in street cams have an ``A`` intake and a long duration exhaust for cooler running and high-end power Suitable for hydraulic lifters The cam for modified or mildly stroked 48-84 Big Twin models Spring spacing required; and clearance at main bearing boss must be checked Offer extra strong mid- and top-end ranges A hydraulic version of Andrews ``B`` grind cams; for 48-84 Big Twin models Most are bolt-in; but spring spacing may be required

CAMS FOR 48-84 BIG TWIN

ANDREWS AB CAM 78-84 BT						$127.95
``AB`` Grind Cam Mfg. #: 212335 Our #: P DS199328 Vendor #: DS-199328
For L77-84 Shovelhead (except for 80-81)

ANDREWS AB CAM 70-77 BT						$127.95
``AB`` Grind Cam Mfg. #: 212320 Our #: P DS199347 Vendor #: DS-199347
For 70-E77 Shovelhead

74 CAM AB GRIND 48-69 BT						$127.95
``AB`` Grind Cam Mfg. #: 212310 Our #: P DS199317 Vendor #: DS-199317
For 48-69 Shovel; Panhead

74 CAM BH GRIND 78-84						$127.95
``BH`` Grind Cam Mfg. #: 212440 Our #: P DS199299 Vendor #: DS-199299
For L77-84 Shovelhead

74 CAM BH GRIND 70-77						$127.95
``BH`` Grind Cam Mfg. #: 212430 Our #: P DS199298 Vendor #: DS-199298
For 70-E77 Shovelhead

74 CAM BH GRIND 48-69						$127.95
``BH`` Grind Cam Mfg. #: 212420 Our #: P DS199297 Vendor #: DS-199297
For 48-69 Shovel; Panhead

74 CAM C GRND 78-84 SHVL						$127.95
``C`` Grind Cam Mfg. #: 212620 Our #: P DS199314 Vendor #: DS-199314
For L77-84 Shovelhead

74 CAM C GRND 70-77 SHVL						$127.95
``C`` Grind Cam Mfg. #: 212610 Our #: P DS199313 Vendor #: DS-199313
For 70-E77 Shovelhead

74 CAM J GRND 78-84 SHVL						$127.95
``J`` Grind Cam Mfg. #: 212030 Our #: P DS199303 Vendor #: DS-199303
For L77-84 Shovelhead

74 CAM J GRND 70-77 SHVL						$127.95
``J`` Grind Cam Mfg. #: 212020 Our #: P DS199302 Vendor #: DS-199302
For 70-E77 Shovelhead

74 CAM J GRND 48-69 BIG-T						$127.95
``J`` Grind Cam Mfg. #: 212011 Our #: P DS199301 Vendor #: DS-199301
For 48-69 Big Twin

CHAIN DRIVEN CAMS

Bolt-in cam with more torque at low and middle rpm range (1;700-5;200 rpm) Similar to EV23 for heavy bikes Work well with either fuel-injection or carburetor Can be used with stock valve springs and tappets Bolt-in cams for low rpm torque and two-up touring Add more torque and horsepower at low and middle rpm range (1;800-5;500 rpm) Work well with either fuel-injection or carburetor Can be used with stock valve springs and tappets Great cams for motors with 9.8 to 10.2 compression ratio Lower TDC lift for easy installation

CHAIN DRIVEN CAMS

CAMS 21H 06DYNA 07-09 TC						$251.95
TW21 Grind Cam Mfg. #: 216321 Our #: P 09250112 Vendor #: 0925-0112
For all 07 Twin Cam and 06 Dyna Glide

TW21CAMS 99-06 TWINCAM						$251.95
TW21 Grind Cam Mfg. #: 288121 Our #: P DS199176 Vendor #: DS-199176
For 00-06 Twin Cam (except 06 Dyna Glide)

CAMS 26H 06DYNA 07-09 TC						$283.95
TW26A Grind Cam Mfg. #: 216326 Our #: P 09250113 Vendor #: 0925-0113
For all 07 Twin Cam and 06 Dyna Glide

TW26ACAMS 99-06 TWINCAM						$251.95
TW26A Grind Cam Mfg. #: 288126 Our #: P DS199179 Vendor #: DS-199179
For 00-06 Twin Cam (except 06 Dyna Glide)

CAMS 31H 06DYNA 07-09 TC						$251.95
TW31S Grind Cam Mfg. #: 216331 Our #: P 09250114 Vendor #: 0925-0114
For all 07 Twin Cam and 06 Dyna Glide

CAM SET TW31S T.C.88						$251.95
TW31S Grind Cam Mfg. #: 288131 Our #: P 09250070 Vendor #: 0925-0070
For 00-06 Twin Cam (except 06 Dyna Glide)

CAMS 32H 06DYNA 07-09 TC						$251.95
TW32H Grind Cam Mfg. #: 216332 Our #: P 09250188 Vendor #: 0925-0188
For all 07 Twin Cam and 06 Dyna Glide

CAMS 37H 06DYNA 07-09 TC						$251.95
TW37B Grind Cam Mfg. #: 216337 Our #: P 09250115 Vendor #: 0925-0115
For all 07 Twin Cam and 06 Dyna Glide

TW37BCAMS 99-06 TWINCAM						$251.95
TW37B Grind Cam Mfg. #: 288137 Our #: P DS199180 Vendor #: DS-199180
For 00-06 Twin Cam (except 06 Dyna Glide)

CAMS 44H 06DYNA 07-08 TC						$176.95
TW44 Grind Cam Mfg. #: 216344 Our #: P 09250116 Vendor #: 0925-0116
For all 07 Twin Cam and 06 Dyna Glide

CAMS 50H 06DYNA 07-09 TC						$251.95
TW50 Grind Cam Mfg. #: 216350 Our #: P 09250117 Vendor #: 0925-0117
For all 07 Twin Cam and 06 Dyna Glide

TW50CAMS 99-06 TWINCAM						$251.95
TW50 Grind Cam Mfg. #: 288150 Our #: P DS199181 Vendor #: DS-199181
For 00-06 Twin Cam (except 06 Dyna Glide)

CAMS 55H 06DYNA 07-09 TC						$251.95
TW Grind Cam Mfg. #: 216355 Our #: P 09250118 Vendor #: 0925-0118
For all 07 Twin Cam and 06 Dyna Glide

TW55CAMS 99-06 TWINCAM						$251.95
TW Grind Cam Mfg. #: 288155 Our #: P DS199178 Vendor #: DS-199178
For 00-06 Twin Cam (except 06 Dyna Glide)

CAMS 60H 06DYNA 07-09 TC						$251.95
TW60A Grind Cam Mfg. #: 216360 Our #: P 09250119 Vendor #: 0925-0119
For all 07 Twin Cam and 06 Dyna Glide

TW60CAMS 99-06 TWINCAM						$251.95
TW60A Grind Cam Mfg. #: 288160 Our #: P DS199182 Vendor #: DS-199182
For 00-06 Twin Cam (except 06 Dyna Glide)

GEAR-DRIVEN CAMS

Andrews Products grinds its cams with the help of a computer with cam design capabilities. This superior technology gives the utmost in both performance and reliability. Only the best alloy steel billets and heat-treating processes are util Bolt-in cam for more torque with stock compression Run best with low restriction exhausts (1700-5200 rpm) Similar to the EV-23 cam Cams work well with fuel injection or carburetor models Can be used with stock valve springs and tappets Works well with carbs or fuel injection Bolt-in cam for lower rpm torque on heavier bikes For two-up touring Good power from 1800-5500 rpm

GEAR-DRIVEN CAMS

CAMS 21HG 06DYNA 07-09 BT						$283.95
21HG Grind Cam Mfg. #: 216321G Our #: P 09250168 Vendor #: 0925-0168
For all 07 Twin Cam and 06 Dyna Glide

21G CAMS 99-06 TWIN CAM						$281.95
21HG Grind Cam Mfg. #: 288121G Our #: P DS199250 Vendor #: DS199250
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 26HG 06DYNA 07-09 BT						$294.95
26HG Grind Cam Mfg. #: 216326G Our #: P 09250169 Vendor #: 0925-0169
For all 07 Twin Cam and 06 Dyna Glide

GEAR DRIVE TW26 CAM						$281.95
26HG Grind Cam Mfg. #: 288126G Our #: P DS199117 Vendor #: DS199117
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 31HG 06DYNA 07-09 BT						$283.95
31HG Grind Cam Mfg. #: 216331G Our #: P 09250170 Vendor #: 0925-0170
For all 07 Twin Cam and 06 Dyna Glide

CAM SET 31G T.C.88						$281.95
31HG Grind Cam Mfg. #: 288131G Our #: P 09250069 Vendor #: 0925-0069
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 32HG 06DYNA 07-09 BT						$283.95
32HG Grind Cam Mfg. #: 216332G Our #: P 09250171 Vendor #: 0925-0171
For all 07 Twin Cam and 06 Dyna Glide

CAMS 32G 99-06 TWIN CAM						$281.95
32HG Grind Cam Mfg. #: 288132G Our #: P 09250180 Vendor #: 0925-0180
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 37HG 06DYNA 07-09 BT						$283.95
37HG Grind Cam Mfg. #: 216337G Our #: P 09250172 Vendor #: 0925-0172
For all 07 Twin Cam and 06 Dyna Glide

37G CAMS 99-06 TWIN CAM						$281.95
37HG Grind Cam Mfg. #: 288137G Our #: P DS199247 Vendor #: DS199247
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 44HG 06DYNA 07-09 BT						$207.95
44HG Grind Cam Mfg. #: 216344G Our #: P 09250173 Vendor #: 0925-0173
For all 07 Twin Cam and 06 Dyna Glide

CAMS 50HG 06DYNA 07-09 BT						$283.95
50HG Grind Cam Mfg. #: 216350G Our #: P 09250174 Vendor #: 0925-0174
For all 07 Twin Cam and 06 Dyna Glide

GEAR DRIVEN TW50 CAMS						$281.95
50HG Grind Cam Mfg. #: 288150G Our #: P DS199118 Vendor #: DS199118
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 55HG 06DYNA 07-09 BT						$283.95
55HG Grind Cam Mfg. #: 216355G Our #: P 09250175 Vendor #: 0925-0175
For all 07 Twin Cam and 06 Dyna Glide

55G CAMS 99-06 TWIN CAM						$281.95
55HG Grind Cam Mfg. #: 288155G Our #: P DS199249 Vendor #: DS199249
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 59HG 06DYNA 07-09 BT						$336.95
59HG Grind Cam Mfg. #: 216359G Our #: P 09250176 Vendor #: 0925-0176
For all 07 Twin Cam and 06 Dyna Glide

59G CAMS 99-06 TWIN CAM						$394.95
59HG Grind Cam Mfg. #: 288159G Our #: P DS199251 Vendor #: DS199251
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 60HG 06DYNA 07-09 BT						$283.95
60HG Grind Cam Mfg. #: 216360G Our #: P 09250177 Vendor #: 0925-0177
For all 07 Twin Cam and 06 Dyna Glide

GEAR DRIVEN TW60 CAMS						$281.95
60HG Grind Cam Mfg. #: 288160G Our #: P DS199119 Vendor #: DS199119
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 67HG 06DYNA 07-09 BT						$283.95
64HG Grind Cam Mfg. #: 216367G Our #: P 09250179 Vendor #: 0925-0179
For all 07 Twin Cam and 06 Dyna Glide

CAMS 67G 99-06 TWIN CAM						$281.95
64HG Grind Cam Mfg. #: 288167G Our #: P 09250181 Vendor #: 0925-0181
For 99-06 Twin Cam (except 06 Dyna Glide)

CAMS 64HG 06DYNA 07-09 BT						$336.95
67HG Grind Cam Mfg. #: 216364G Our #: P 09250178 Vendor #: 0925-0178
For all 07 Twin Cam and 06 Dyna Glide

64G CAMS 99-06 TWIN CAM						$394.95
67HG Grind Cam Mfg. #: 288164G Our #: P DS199252 Vendor #: DS199252
For 99-06 Twin Cam (except 06 Dyna Glide)

TWIN CAM CONVERSION CAMSHAFTS

Allows you to upgrade your 99-06 Twin Cam (except 06 Dyna Glide) to the newer roller-style cam chains and replaces the spring tension cam chain adjusters with the laterstyle hydraulic adjusters for longer life. Cam grinds listed are designed to be used with stock lifters. They require the installation of a 2007 cam plate; oil pump; cam sprockets and chains; and both hydraulic chain adjusters. These parts are not included and must be purchased sepa Performance should be similar to earlier bikes with the same cam grinds Bolt-in cams with the same output as the stock cams Slight power increase when compared to stock No retuning of the stock system is necessary Can be used with stock valve springs and tappets Bolt-in cams with more torque at low and middle rpm range (1700-4800 rpm) Similar to EV23 for heavy bikes Ideal for heavy bikes with stock compression ratios and stock pistons

TWIN CAM CONVERSION CAMSHAFTS

CAM ROLLER CONVER. 12N						$251.95
Mfg. #: 216812 Our #: P 09250139 Vendor #: 0925-0139
``12N`` Grind Cam

CAM ROLLER CONVER. 26N						$251.95
Mfg. #: 216826 Our #: P 09250141 Vendor #: 0925-0141
``26N`` Grind Cam

CAM ROLLER CONVER. 37N						$251.95
Mfg. #: 216837 Our #: P 09250143 Vendor #: 0925-0143
``37N`` Grind Cam

CAM ROLLER CONVER. 50N						$251.95
Mfg. #: 216850 Our #: P 09250145 Vendor #: 0925-0145
``50N`` Grind Cam

CAM ROLLER CONVER. 21N						$251.95
Mfg. #: 216821 Our #: P 09250140 Vendor #: 0925-0140
``21N`` Grind Cam

CAM ROLLER CONVER. 31N						$251.95
Mfg. #: 216831 Our #: P 09250142 Vendor #: 0925-0142
``31N`` Grind Cam

CAM ROLLER CONVER. 55N						$251.95
Mfg. #: 216855 Our #: P 09250146 Vendor #: 0925-0146
``55N`` Grind Cam

XL AND BUELL CAMS

Cams run to 6500 rpm with stock hydraulic lifters; recommend solids not be installed Stock base circle sizes allow the use of stock pushrods V2 and N2 are bolt-in cams for stock applications designed for up to 6000 rpm N3 cam is bolt-in for 05-06 883/1200 engines with stock springs & heads (cams for 04-06 models with more than .465 lift may need different valves; springs and collars) V4 and N4 are for stock or modified applications and have a slightly higher idle speed; but can be used with stock hydraulic lifters and springs; rpm range of 2500-6500 V6 and N6 designed for modified 1200s to 80`` and/or high compression pistons: stock springs and hydraulic lifters recommended; rpm range 2500-6500 V8 and N8 designed for modified 883; 1100 and 1200 stroker models; stock springs and hydraulic lifters recommended; rpm range 2000-6000 N6 designed for modified 1200s to 80`` and/or high compression pistons: stock springs and hydraulic lifters recommended; rpm range 2500-6500 N8 designed for modified 883; 1100 and 1200 stroker models; stock springs and hydraulic lifters recommended; rpm range 2000-6000 B50 designed for more valve lift and duration; stock hydraulics and springs; more power and torque 2000 to 6000 rpm

XL AND BUELL CAMS

CAMS``Y``GRIND F/71-E84XL						$356.95
Mfg. #: 214080 Our #: P DS199356 Vendor #: DS-199356
FOR: XL 71-E84 - ``Y`` Cam

CAMS R5 GRIND F/71-E84XL						$356.95
Mfg. #: 214110 Our #: P DS199355 Vendor #: DS-199355
FOR: 71-E84 XL - ``R5`` Cam

CAM PB+GRIND 1 4 71-E84XL						$178.95
Mfg. #: 214014 Our #: P DS199345 Vendor #: DS-199345
FOR: 71-E84 XL - ``PB+`` Exhaust Cam

B50 CAM SET 00-06 BLAST						$191.95
Mfg. #: 297150 Our #: P DS199254 Vendor #: DS199254
FOR: 00-06 Buell Blast - B50 Grind Cam Set

B70 CAM SET 00-06 BLAST						$191.95
Mfg. #: 297170 Our #: P DS199255 Vendor #: DS199255
FOR: 00-06 Buell Blast - B70 Grind Cam Set

ANDREWS N2 CAM 91-99 XL						$289.95
For 91-99 XL and 94-99 Buell Mfg. #: 298125 Our #: P DS199195 Vendor #: DS-199195
N2 cams

ANDREWS N4 CAM 91-99 XL						$289.95
For 91-99 XL and 94-99 Buell Mfg. #: 298145 Our #: P DS199196 Vendor #: DS-199196
N4 cams

ANDREWS N6 CAM 91-99 XL						$289.95
For 91-99 XL and 94-99 Buell Mfg. #: 298165 Our #: P DS199114 Vendor #: DS-199114
N6 cams

ANDREWS N8 CAM 91-98 XL						$289.95
For 91-99 XL and 94-99 Buell Mfg. #: 298185 Our #: P DS199112 Vendor #: DS-199112
N8 cams

ANDR V2 CAM EV XL 86-90						$289.95
For 86-90 XL Mfg. #: 298120 Our #: P DS199295 Vendor #: DS-199295
V2 cams

ANDR V4 CAM EVO XL 86-90						$289.95
For 86-90 XL Mfg. #: 298140 Our #: P DS199296 Vendor #: DS-199296
V4 cams

ANDREWS V6 CAM 86-90 XL						$289.95
For 86-90 XL Mfg. #: 298160 Our #: P DS199113 Vendor #: DS-199113
V6 cams

ANDREWS V8 CAM 86-90 XL						$289.95
For 86-90 XL Mfg. #: 298180 Our #: P DS199111 Vendor #: DS-199111
V8 cams

ANDREWS N2 CAM 00-09 XL						$289.95
For 00-06 XL and 00-02 Buell (Except XB9R) Mfg. #: 298130 Our #: P DS199075 Vendor #: DS-199075
N2 cams

CAM SET N3 05-06 XL						$289.95
For 00-06 XL and 00-02 Buell (Except XB9R) Mfg. #: 298135 Our #: P 09250072 Vendor #: 0925-0072
N3 cams (05-06 XL models only)

ANDREWS N4 CAM 00-09 XL						$289.95
For 00-06 XL and 00-02 Buell (Except XB9R) Mfg. #: 298150 Our #: P DS199076 Vendor #: DS-199076
N4 cams

ANDREWS N6 CAM 00-09 XL						$289.95
For 00-06 XL and 00-02 Buell (Except XB9R) Mfg. #: 298170 Our #: P DS199077 Vendor #: DS-199077
N6 cams

ANDREWS N8 CAM 00-09 XL						$289.95
For 00-06 XL and 00-02 Buell (Except XB9R) Mfg. #: 298190 Our #: P DS199078 Vendor #: DS-199078
N8 cams

home > andrews > brand index > cams home > andrews > product index > cams

Link to ANDREWS Website

ANDREWS - CAMS

CAMS

home > andrews > brand index > cams
home > andrews > product index > cams